On February 25, 1999, about 1008 eastern standard time, a Mooney M20J, N4671H, registered to Trophy 212 Inc., collided with trees while descending for a forced landing to a field near St. Cloud, Florida. Visual meteorological conditions prevailed at the time and no flight plan was filed for the 14 CFR Part 91 personal flight. The airplane was substantially damaged and there were no reported injuries to the private-rated pilot or two passengers. The flight originated about 33 minutes earlier from the St. Lucie County International Airport, Fort Pierce, Florida. The pilot stated that while descending through 2,800 feet, he noted a slight vibration when the throttle only was reduced. He then felt a jolt and the windscreen was covered with oil. He reduced the throttle to idle and initiated a descent for a forced landing. While descending about 25 feet agl, the left wing of the airplane collided with a tree. The airplane then touched down with the gear retracted, bounced, and came to rest upright. Examination of the airplane by an FAA airworthiness inspector revealed that one of the two propeller blades was fractured with only a segment of the butt end of the blade remaining inside the propeller hub. A crack in the radius of the crankshaft flange which extended approximately 30 percent circumferentially was noted adjacent to the missing propeller blade. Engine oil was noted on the windshield and portion of the fuselage. The alternator, starter, exhaust system, and air induction system were separated. The engine mount was broken and one of the lord mounts was split. The engine was noted to be shifted aft and the front portion of the engine was contacting the ground with the bottom rear portion of the engine nearly contacting the firewall. The landing gear and flaps were determined to be retracted and damage to the leading edge of the left wing due to contact with a tree was noted 2 feet inboard from the wing tip. Examination of the cockpit revealed that the compass was broken from its mount location as was the column mounted GPS. A placard required by the Type Certificate data sheet pertaining to engine rpm was installed beneath the electronic tachometer. The engine and propeller assembly were recovered for further examination. Examination of the propeller assembly while installed on the engine revealed five balance washers attached to the propeller spinner bulkhead. The propeller spinner and propeller spinner bulkhead were noted to be almost completely separated from the propeller. The propeller was removed from the engine and during removal, the torque on the attach bolts was noted to be "light." The bolts were properly safety wired and each had one washer under the bolt. The roll pins were determined to be in good condition. Visual examination of the propeller hub revealed no evidence of cracks. Evidence at the bolt holes was the indication that the propeller came in contact with the elevated sleeves at one time. The propeller was retained for further examination. Examination of the detached propeller assembly revealed that the No. 2 propeller blade was not bent but did exhibit scratches at the leading edge of the blade near the propeller hub. The No. 2 propeller blade was dye penetrant inspected; no cracks were detected. The No. 1 propeller blade was fractured and separated; with only a segment remaining inside the propeller hub. Fretting was noted on the face of the propeller hub and mechanical damage was noted aft of the o-ring to the inside surface of the pilot bore of the propeller hub. Two slivers of aluminum were found inside the pilot bore. Five washers associated with static balancing were noted adjacent to the No. 2 propeller blade. Disassembly of the propeller revealed that the No. 1 propeller blade phoenolic actuating pin link was broken; the actuating pin was not broken. The No. 2 propeller blade outer bearing race which was determined to be cracked, the two segments of the No. 1 propeller blade that were retained in the propeller hub, and the propeller hub were submitted to the NTSB Materials Laboratory located in Washington, D.C., for metallurgical examination. A copy of the report from the propeller manufacturer is an attachment to this report. Metallurgical examination of the two segments of the No. 1 propeller blade revealed that the blade was fractured through the relief radius just outboard of the blade retainer shelf. Three fatigue origin areas were detected each with its own area of propagation on the fracture. No mechanical or corrosion damage was noted in the radius at any of the origin areas. The three fatigue regions accounted for more than 60 percent of the fracture surface and the remaining fracture surface consisted of bending overstress stemming from the fatigue regions. Hardness tests and electrical conductivity measurements on the outer diameter were consistent with the specified heat treatment condition. Examination of the No. 2 outer bearing race revealed the fracture features were typical of an overstress separation. A copy of the report is an attachment to this report. Metallurgical examination of the propeller hub revealed light fretting over large areas of the face of the hub with severe fretting noted in the areas inboard of the bolts. Severe mechanical damage to the pilot hole bore was noted along with linear gouges and plastic deformation around slightly less than half of the perimeter of the hole. The damaged arc was located on the No. 2 propeller blade side of the bore and raised lips on the forward edges of the gouges were noted. The gouges were angled across the pilot bore between 10-15 degrees from vertical with the propeller hub face positioned in a normally installed position parallel to the engine crankshaft flange. Review of the maintenance records revealed the first entry pertaining to a production test flight was dated May 7, 1979. An entry dated September 5, 1980, indicates that a factory new propeller was installed; the airplane had accumulated 278 hours total time at that time. The propeller was overhauled on December 23, 1986, resealed only on September 14, 1988, and on March 13, 1990, the seals were replaced to correct grease leakage. The final work performed to the propeller was accomplished on July 9, 1997, in which the serviceable tag indicates "reseal only." The propeller was approved for return to service that same day. The entry in the aircraft logbook dated July 15, 1997, indicates "removed & reinstalled propeller after resealing from El Paso Propeller Test ran leak check ok (yellow tag in engine logbook)" The entry was signed and listed an A&P certificate number 450135494. There was no other entry in the maintenance records pertaining to the propeller. The propeller had accumulated 150.81 hours since last installed at the time of failure. The airplane minus the retained propeller hub, the two pieces of the No. 1 propeller blade, the cracked outer bearing race from the No. 2 propeller blade, two each aircraft logbooks, one each engine logbook, propeller yellow tags, and other maintenance records was released to Stephen W. Pulak, Insurance Adjuster for Sample International, Inc., on September 21, 1999. The retained components and records were released to Faith A. Collins, President of Sample International, Inc., on October 1, 1999.