HISTORY OF FLIGHT On May 2, 1997, approximately 1515 Pacific daylight time, a homebuilt Hendrix Talon XP, N6291X, being flown by the owner/builder, a private pilot, was substantially damaged during impact with terrain following a loss of control in flight while entering downwind to land at the Cline Falls private airstrip, Redmond, Oregon. The pilot, occupying the forward seat, sustained minor injuries. Visual meteorological conditions existed at the time and no flight plan had been filed. The flight, which was personal, was to have been operated under 14CFR91, and originated from Sisters, Oregon, approximately 1443 local time. The pilot reported that en route to Smith Rock's State Park he encountered light to moderate thermal turbulence and "heard & lightly felt a popping noise in the forward fuselage" and also "lightly felt it in the stick." He then turned toward Kline Falls and "noticed mushy aileron controls" in the turn. The pilot reported entering downwind for runway 27 during which the degradation of aileron and elevator control increased. He reported that shortly thereafter, "something broke (and) left me with a stick that flopped around (&) no control of the aircraft." The pilot then actuated the aircraft's ballistic parachute less than 150 feet above ground. The parachute opened and the aircraft decelerated missing a power pole and coming to rest nearby (refer to photograph 1 which shows the damaged aircraft subsequent to its recovery). AIRCRAFT INFORMATION The kitplane, a tandem seat Sportflight Aviation, Inc., Talon XP, serial number 115XP, was purchased and assembled by the pilot/owner and was issued a Special Airworthiness Certificate with an experimental designation on October 18, 1996. The operating limitations for the kitplane were issued on September 18, 1996 (refer to ATTACHMENT OL-I). Item 6 (page 1 of ATTACHMENT OL-I) states: "No Person may be carried in this aircraft during flight unless that person is required for the purpose of flight." (Note: this applies to the initial 40 hours of flight operations of the kitplane). Subsequent to the accrual of 40 hours of flight operations, a passenger may be carried in the aircraft so long as the requirements of Item 5 (page 2 of ATTACHMENT OL-I) are met (defined as follows): "No person may operate this aircraft for carrying persons or property for compensation or hire" The aircraft had a total of approximately 70 hours of airframe (operating) time when it crashed. Additionally, the pilot/owner installed a Ballistic Recovery Systems, Inc., ballistic parachute, model BRS-750 "softpack." This system was installed above the aircraft's wing center section, along the longitudinal axis, and was designed to serve as a parachute for both the aircraft and its occupant(s). WRECKAGE AND IMPACT INFORMATION Post crash examination of the aircraft was conducted by an Inspector from the Federal Aviation Administration's Hillsboro Flight Standards District Office. The inspector determined that the torque tube which translates fore and aft (elevator movement) and left and right (aileron movement) from the control sticks, had separated at the forward end of the tube (just forward of the forward torque tube guide) as shown in photograph 2. Further examination revealed that although the forward control stick had been attached to the torque tube, the aft control stick had not been installed. Additionally, the control stick interlink tube had not been installed (refer to photograph 3 and ATTACHMENTS I & II). TEST AND RESEARCH Examination of the separation surfaces from the torque tube revealed torsional overload consistent with sideways stick movement associated with aileron inputs. Examination of the assembly drawing for the aircraft's fore and aft control stick assembly (ATTACHMENT II) revealed that both the forward and aft sticks coupled to the fore and aft ends of both the torque tube and the interlink tube to create a "box" unit with structural integrity formed by the four connection points (refer to "Assembled View" insert in ATTACHMENT II). The interlink tube, which rides within the torque tube, extends out through the torque tube radius through a slot cut in the underside of each end of the tube. The fore and aft ends of the interlink tube attach to the respective fore and aft control sticks via bolts (refer to photograph 4). There was no caution note within the kitplane assembly instructions advising the builder that failure to install either the aft control stick and/or interlink tube would result in a compromise of the structural integrity of the fore and aft stick, torque tube and interlink tube assembly. ADDITIONAL INFORMATION The forward control stick, torque tube and interlink tube, along with associated paperwork for the aircraft, which were shipped to the Safety Board by the FAA Inspector (noted above), were returned to the pilot/owner on February 4, 1998, via certified mail.