HISTORY OF FLIGHT On November 9, 2004, about 1215 Pacific standard time, an American Eurocopter AS350-BA, N655TV, was executing an autorotation when the collective flight control became locked, and the helicopter made a hard landing at Oxnard Airport, Oxnard, California. Coastal Helicopters LLC was operating the helicopter under the provisions of 14 CFR Part 91. The certified flight instructor (CFI) pilot and the commercial pilot undergoing instruction (PUI) sustained minor injuries; the helicopter sustained substantial damage. The instructional local flight departed Camarillo, California, at about 1100. Visual meteorological conditions prevailed, and no flight plan had been filed. The primary wreckage was located at 34 degrees 11.982 minutes north latitude and 119 degrees 13.109 minutes west longitude. The purpose of the instructional flight was recurrent factory pilot training for the PUI. The CFI was a factory pilot, employed by American Eurocopter Corporation (AEC), located in Grand Prairie, Texas. The National Transportation Safety Board investigator-in-charge (IIC) interviewed the CFI and the PUI. Both pilots stated that while performing an intended power recovery autorotation, the collective locking mechanism inadvertently engaged, preventing the PUI from applying any pitch to the main rotor system by use of the collective lever. Both pilots attempted to unlock the collective but were unsuccessful before the helicopter impacted the ground. After the accident sequence, the helicopter came to rest on its right side. Investigators from the Safety Board, the Federal Aviation Administration (FAA), American Eurocopter, and Turbomeca USA examined the wreckage at Oxnard Airport on November 11, 2004. During the wreckage examination, no abnormalities were found with the engine, flight controls, or rotor system. One area of concern during this investigation was with the collective locking mechanism. The helicopter was equipped with an aftermarket avionics console. The console, model P132, was manufactured by Geneva Aviation, Inc. Aircraft records indicated it had been installed on November 11, 2002, in accordance with instructions provided in the supplemental type certificate (STC) number SH4747NM. The larger Geneva P132 Avionics Switch Console replaces the stock AEC console and replaces the stock auto type fuses with Mil-spec circuit breakers. The console also allows for the installation of additional avionics. The footprint dimensions of the Geneva console are approximately the same as the stock panel. The front height of the Geneva console is approximately 13 inches. The front height of the stock console is approximately 11 inches. The accident helicopter's console was damaged during the accident sequence. Measurements of the clearance between the collective engagement stud and the locking plate were inconclusive due to the impact damage to the console. Upon examination, the accident helicopter's console appeared to be installed in accordance with the installation instructions for the STC. Exemplar aircraft with the stock console and the Geneva console were examined, measured, and photographed. The collective lever lock is installed on the console; it is a spring steel plate with a hole in it to capture the collective locking tab. The lock also has a rubber grommet below the locking hole to dampen any vibration. The stock AEC console with the collective in the full down position has about a 1/2-inch clearance between the collective lever lock and the collective locking tab. The Geneva console with the collective in the full down position has about a 1/16-inch clearance. During the exemplar aircraft examinations, both the ones equipped with the stock and ones equipped with the Geneva console, in some of the aircraft, the grommet was not touching the console. This condition would allow the locking lever to vibrate and also decrease the clearance between the locking plate and the locking tab. On July 1, 2004, a similar accident (NTSB accident LAX04LA254) occurred in Scottsdale, Arizona. This involved a Eurocopter AS350 B2. In this accident, the flight crew was performing a maintenance check flight after a major overhaul that included the installation of a Geneva console. The flight crew reported the collective locking mechanism inadvertently engaged. A post impact fire consumed the aircraft. This accident is currently under investigation, and no final report has been filed. On December 2, 2004, the FAA issued a Special Airworthiness Information Bulletin (SAIB) alerting all owners and operators of all Eurocopter France AS-350 and AS-355 rotorcraft that have aftermarket center console panels installed, that preliminary investigations reveal a potentially hazardous situation in which the collective lock strip inadvertently engages during flight maneuvers, locking the collective in the down position. The SAIB made the following recommendations; Inspect the condition of the collective locking strip, P/N 350A27-3107-26, to ensure the strip has a positive spring force to hold it away from the collective knob and firmly against the center console. Inspect and ensure the rubber grommet, P/N 85007-130-015, is resting against the center console. To ensure proper rigging of the collective, review AS-350 collective lock rigging procedures, Work Card 67.10.00.501 without autopilot, and Work Card 67.10.00.502 with autopilot. Ensure that there is a positive clearance (nominally 7mm) between the collective lock knob, P/N 350A77-1309-24, and the collective strip. Ensure the aftermarket installation is installed as to allow proper clearance for the collective lock at all times. Ensure the collective lock spring mounting bolts are secure and torque properly, 35-44 in. ADDITIONAL INFORMATION The IIC released the wreckage to the owner's representative on November 12, 2004.